R2AK Day 11 - Inside Passage's Spectacular Greville Channel


by Julie Angus


Colin Angus near Ivory Island, Seaforth Channel on July 4 (Photo Credit: Bob & Lois Stevenson on SV Passages, 42' Jeanneau)Colin is currently anchored in Klewnuggit, just outside the marine provincial park.  He’s about 40 kilometers south of where the Skeena River flows into the Pacific. Dale McKinnon, who is very familiar with these waters, describes the confluence of the Skeena and tidal waters as notorious in a flood tide and even challenging in an ebb tide.  Tomorrow he’ll be travelling these waters, so fingers crossed that all goes well.

Today he left his anchorage at about 5 am, crossed over to Gribbell Island and hugged the southern coast of it before making a 10 km crossing of Wright Sound.  Wright Sound is where in 2006, BC Ferry’s Queen of the North disastrously ran aground and sunk, killing 2 people. Colin then entered the Grenville Channel, a 70 km long channel that is described as the most spectacular channel along the Inside Passage. It is sandwiched by towering mountains and narrows to a mere 1400 ft in some areas.

According to the weather report it’s been a grey rainy day with light winds in that area.  However, the high mountains and narrow inlet can create a funnelling effect for both winds and currents.  Colin pulled into his current anchorage around 4:30 pm, which is early for him, so I suspect conditions were not ideal.

Update:  Colin called Small Craft Advisor and left an update .  Here it is, courtesy of their FB page.

Colin (Team Angus Rowboats) checked in from a nice anchorage near Klewnuggit Inlet. He says he made good progress today courtesy of strong tailwinds and a tremendous favorable current that had him doing a long stretch at 8 knots.

He'd planned to push on further tonight but came around a turn in the narrow channel route he's chosen to find a 20-knot headwind stacking up against the current, so he decided to aim for the nearby inlet and anchorage.

Colin say the steep mountains come right down to rocky shores and there are far fewer anchorages and almost no beaches to be found. In fact he says it was a bit disconcerting at his anchorage last night when the wind clocked around onshore blowing over lots of fetch at the craggy shoreline. And I'm guessing it probably didn't help that he'd seen his first bear on that same strip of land earlier in the evening . Fortunately the winds never really came up.

He and the boat are doing great, although his auto-pilot, which had been making funny noises and which he's come to rely on, finally quit entirely. He installed his backup unit and says it's performing great. Who says you can't carry everything you need on an 18-foot rowboat?




Julie Angus
Julie Angus

Author



Leave a comment

Comments will be approved before showing up.


Also in News

Human Powered Achievements through the Northwest Passage
Human Powered Achievements through the Northwest Passage

by Julie Angus

At Angus Rowboats, our passion for adventure naturally draws us to the mystique of the Northwest Passage – one of the world's most captivating and perilous waterways. Historically, this elusive passage promised a shorter shipping route, spurring early navigators to fervently chart and struggle through its icy intricacies.

The summer of 2023 saw three audacious teams, including one using our very own RowCruiser boats, aiming to be the first to traverse NW Passage solely by human power within a single season. As the season concludes, we've chronicled these attempts, and catalogued past human-powered endeavors to navigate the Northwest Passage.

Read More

Creating a Bookcase from a Boat
Creating a Bookcase from a Boat

by Colin Angus

A good boat is a versatile boat.  Our wheelbarrow boat is good in and out of the water.  It can be used to haul bags of concrete around the construction site, is a vehicle to go crabbing with the kids, or it can be transformed into an elegant bookcase.

Read More

CNC - Cut Kits for Angus Rowboat's Customers Outside of North America
CNC - Cut Kits for Angus Rowboat's Customers Outside of North America

by Julie Angus

Our boat kits are shipped from the PNW, and delivered to customers in the US and Canada.  Due to prohibitive shipping costs, we do not ship our boat kits outside of North America.  Building from plans is one alternative, however, some would prefer to build from a kit.

Read More